955N Wheel Type Loader
- · Full way solution
- · Consistent quality
- · Top end Design
- · Increased operating reliability
- · Excellent lifetime precision
- · Production cost saving
- · High Efficiency
- · Electrical control
Product Features
1. Adopting high power, low speed, high efficiency of weichai engine, good reliability, conform to the European Ⅱ emissions standards.The dual variable assembly adopts ZL50 type planetary gearbox with low speed engine, double turbine assembly, strong market and convenient accessories.The gearbox is also a mainstream configuration in the industry, with high reliability and a second step forward, especially a speed ratio of more than 30%.
2. The transmission shaft adopts the special transmission shaft of the key block type engineering machinery, with strong impact resistance and assurance the reliability of transmission.Double pump combined hydraulic system is adopted to improve the oil temperature of hydraulic system, extend the life of hydraulic components, and greatly reduce fuel consumption and energy consumption.At the same time, it will turn to the pump, improve the performance of the idle speed, and reduce the steering force.Hydraulic load sensing steering hydraulic system to light and flexible;The hydraulic system is operated by flexible shaft to reduce the failure point of hydraulic system.
3. Adopt the new view cabin, and according to the principle of ergonomics design, pay attention to the comfort of manipulation, greatly reduce the internal noise, monolithic columns, control handle used car design, relaxed and comfortable.In addition, to fully consider humanization in the maintenance aspect, use the large open type of car cover, the maintenance man can only stand on the ground, and have the engine and other parts.Improve seal reliability, reduce leakage, and change the hose connection to 24 taper + O ring structure, and increase the protection of piston rod.
4. The engine selects the weichai, the torque converter selects the hangers, the tire selects the jiangsu tire factory and other famous domestic brands.
Parameters
| Number | Entry name | Parameter | |
| 1 | Rated weight load(kg) | 5000 | |
| 2 | Bucket capacity(m³) | 3 | |
| 3 | Operating weight(kg) | 16500（1±5％） | |
| 4 | Max dump height(mm) | 3050(45° unloading angle) | |
| 5 | Max reach(mm) | 1107 (45° unloading angle) | |
| 6 | Tread(mm) | 2200 | |
| 7 | Axle-base(mm) | 3100 | |
| 8 | Min steering angle（mm） | 450 | |
| 9 | Max overall height(°) | 38 | |
| 10 | Overall length(mm) | 8200(Bucket flat ground) | |
| 11 | Max overall height(mm) | 3450 | |
| 12 | Overall width(mm) | 2800 | |
| 13 | Bucket width(mm) | 2946 | |
| 14 | Distance between rear axle hinge(mm) | 1750 | |
| 15 | length of rear overhang(mm) | 2210 | |
| 16 | Departure angle(°) | 27 | |
| 17 | Offload angle(°) | 45 | |
| 18 | Max height of rear axle while lifting(mm) | 4055 | |
| 19 | Max overall height while lifting(mm) | 5250 | |
| 20 | Lateral swing angle of rear axle(°) | 11 | |
| 21 | Max rotary angle(°) | Ground position | 43(Hinge pin height:220mm) |
| Material transport position | 48 (Hinge pin height:440mm) | ||
| Max lifting time | 61(Hinge pin height:4055mm) | ||
| 22 | Max gradient(mm) | 440 | |
| 23 | Max traction(KN) | 165 | |
| 24 | Min turning radius(mm) | 5970 | |
| 25 | Turning radius of the bucket while transporting material position(mm) | 6575 | |
| 26 | Max gradient(°) | 30 | |
| 27 | Max side sump load(KN) | 100 | |
| 28 | Max breakout force(KN) | 170 | |
| 29 | Gearbox type | Planetary power shift | |
| 30 | Tire type / manufacturer | 23.5-25/Jiangsu tire factory | |
| 31 | Tire pressure（MPa） before / after | 0.32/0.30 | |
| 32 | Main drive type / deceleration ratio | One step deceleration of spiral bevel gear/5.285 | |
| 33 | Wheel side deceleration type / deceleration ratio | Cylindrical spur gear planetary transmission/4.4 | |
| Number | Entry name | Parameter | |
| 34 | Operating time of working device(s) | Frontal lifting(s) | ≤6.2 |
| No load drop (s) | ≤3.8 | ||
| Bucket forward(s) | ≤1.8 | ||
| 35 | Multiway valve | Model | D32Ⅱ |
| Structure characteristics | Flexible shaft control | ||
| Setting pressure（MPa） | 19 | ||
| 36 | Engine | model/manufacturer | WD10G220E23/Weichai power Co., Ltd. |
| Type | Six cylinder, inline, water cooling, four stroke, supercharging | ||
| Power（KW） | 162 | ||
| Speed（r/min） | 2000 | ||
| Fuel consumption rate（g/kwh） | ≤210 | ||
| Max torque（N.M） | 900 | ||
| 37 | Hydraulic system of working device | System working pressure（MPa） | 19 |
| Oil pump model / production plant | JHP2080S / Ji'nan hydraulic pump Co., Ltd. | ||
| Oil pump displacement（ml/r） | 80 | ||
| Boom cylinder(mm) | 2-Ø160×705 | ||
| Bucket cylinder(mm) | 1- Ø180×530 | ||
| 38 | Torque converter | Type | Dual turbine four wheel |
| Manufacturer | Hangzhou Qianjin gear box Group Co., Ltd. | ||
| 39 | Running speed（km/h） | Forward I / II gear | 0～12.1/0～37.4 |
| Back Ⅰ gear | 0～16.5 | ||
| 40 | Foot brake type / brake oil pressure | Gas cap oil clamp disc/0.8 | |
| 41 | Hand brake type | Inner raised drum flexible shaft control | |
| 42 | Steering system | System working pressure（MPa） | 16 |
| Steering pump model / manufacturer | JHP2080S / Ji'nan hydraulic pump Co., Ltd. | ||
| Displacement of steering pump（ml/r） | 80 | ||
| Steering gear type / manufacturer | BZZS-E1000/Zhenjiang hydraulic parts General Factory | ||
| Steering cylinder(mm) | 2-Ø90×400 | ||
| 43 | Filling oil quantity | Fuel tank（L） | 250 |
| Crankcase of engine（L） | 42 | ||
| Torque converter and gearbox（L） | 45 | ||
| Hydraulic oil tank（L） | 180 | ||
| Main drive of front and rear axles（L） | 2×18 | ||
| Wheel side reducer（L） | 4×3.5 | ||
| Braking system（L） | 2×1.5 | ||
RELATED PRODUCTS
-
SC200/200Z Construction Hoist
-
QTZ400(TC7050) Tower Crane
-
GSK5420THB52R Truck-Mounted Concrete Pump
